- r -

• raw_to_mm() : FilamentWidthSensor
• Read() : BulkOnly
• read() : DigitalPin< PinNumber >
• Read() : GCodeThumbDecoder
• read() : HalSerial , HardwareSerial , libServo , MarlinSerial< Cfg > , RingBuffer< T, S > , SdBaseFile , Servo , SoftwareSerial , SPIClass , Stream , TwoWire
• Read() : UHS_Bulk_Storage
• read() : USBSerial , WebSocketSerial
• read_buttons() : XPT2046
• read_data() : PersistentStore
• readBlock() : Sd2Card
• readBytes() : Stream , USBSerial
• readBytesUntil() : Stream , USBSerial
• readCID() : Sd2Card
• readCSD() : Sd2Card
• readData() : Sd2Card
• readDir() : SdBaseFile
• reading_ready() : FilamentWidthSensor
• readings_ready() : Temperature
• readMicroseconds() : Servo
• readStart() : Sd2Card
• readStatus() : TMC26XStepper
• readStop() : Sd2Card
• readString() : Stream
• readStringUntil() : Stream
• ready() : Sd2Card
• rebuild() : auto_build.output_window
• receive() : BinaryStream , SoftSPI< MisoPin, MosiPin, SckPin, Mode > , SPIclass< MisoPin, MosiPin, SckPin > , SPIclass< MISO_PIN, MOSI_PIN, SCK_PIN >
• reciprocal() : XYval< T > , XYZEval< T > , XYZval< T >
• recv() : SPIClass
• refresh() : Max7219 , SpindleLaser
• refresh_collector() : Mixer
• refresh_line() : Max7219
• refresh_positioning() : Planner
• refresh_unit_line() : Max7219
• register_setup() : Max7219
• RegisterDeviceClass() : USB
• regRd() : MAX3421e
• regWr() : MAX3421e
• reinit() : Bresenham< T, Cfg >
• relay() : TWIBus
• Release() : BulkOnly , USBDeviceConfig
• ReleaseDevice() : USB
• remove() : SdBaseFile
• rename() : SdBaseFile
• report() : Bresenham< T, Cfg > , MarlinSettings
• report_current_mesh() : unified_bed_leveling
• report_error() : I2CPositionEncodersMgr
• report_error_count() : I2CPositionEncodersMgr
• report_mesh() : mesh_bed_leveling
• report_module_firmware() : I2CPositionEncodersMgr
• report_position() : I2CPositionEncodersMgr
• report_positions() : Stepper
• report_state() : unified_bed_leveling
• report_status() : I2CPositionEncodersMgr
• request() : TWIBus
• requestFrom() : TwoWire
• Reset() : Base64StreamDecoder
• reset() : BinaryStream::Packet::Footer , BinaryStream::Packet::Header , BinaryStream::Packet , BinaryStream , GCodeParser
• Reset() : GCodeThumbDecoder
• reset() : heater_idle_t , I2CPositionEncoder , MarlinSettings , MAX3421e , mesh_bed_leveling , MMU2 , PrintCounter , RunoutResponseDebounced
• Reset() : SLine
• reset() : Stopwatch , TempInfo , TFilamentMonitor< RESPONSE_T, SENSOR_T > , TWIBus , unified_bed_leveling , XYval< T > , XYZEval< T > , XYZval< T >
• reset_acceleration_rates() : Planner
• reset_bed_idle_timer() : Temperature
• reset_error_count() : I2CPositionEncodersMgr
• reset_heater_idle_timer() : Temperature
• reset_stepper_timeout() : GcodeSuite
• reset_vtools() : Mixer
• ResetHubPort() : USBDeviceConfig
• ResetHubPreMask() : USB
• resist() : createTemperatureLookupMarlin.Thermistor
• resol() : createTemperatureLookupMarlin.Thermistor
• restore() : restorer< T >
• restore_ubl_active_state_and_leave() : unified_bed_leveling
• restorer() : restorer< T >
• resume() : PrintJobRecovery , Stopwatch
• resync() : Endstops
• rewind() : SdBaseFile
• RingBuffer() : RingBuffer< T, S >
• rmdir() : SdBaseFile
• rmRfStar() : SdBaseFile
• rootDirEntryCount() : SdVolume
• rootDirStart() : SdVolume
• run() : FilamentSensorSwitch , RunoutResponseDebounced , TFilamentMonitor< RESPONSE_T, SENSOR_T >
• rxMaxEnqueued() : MarlinSerial< Cfg >