Prusa MINI Firmware overview
stm32f4xx_hal_conf.h
Go to the documentation of this file.
1 /**
2  ******************************************************************************
3  * @file stm32f4xx_hal_conf.h
4  * @brief HAL configuration file.
5  ******************************************************************************
6  * @attention
7  *
8  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
9  * All rights reserved.</center></h2>
10  *
11  * This software component is licensed by ST under BSD 3-Clause license,
12  * the "License"; You may not use this file except in compliance with the
13  * License. You may obtain a copy of the License at:
14  * opensource.org/licenses/BSD-3-Clause
15  *
16  ******************************************************************************
17  */
18 
19 /* Define to prevent recursive inclusion -------------------------------------*/
20 #ifndef __STM32F4xx_HAL_CONF_H
21 #define __STM32F4xx_HAL_CONF_H
22 
23 #ifdef __cplusplus
24 extern "C" {
25 #endif
26 
27 /* Exported types ------------------------------------------------------------*/
28 /* Exported constants --------------------------------------------------------*/
29 
30 /* ########################## Module Selection ############################## */
31  /**
32  * @brief This is the list of modules to be used in the HAL driver
33  */
34 #define HAL_MODULE_ENABLED
35 #define HAL_ADC_MODULE_ENABLED
36 /* #define HAL_CAN_MODULE_ENABLED */
37 /* #define HAL_CAN_LEGACY_MODULE_ENABLED */
38 #define HAL_CRC_MODULE_ENABLED
39 /* #define HAL_CEC_MODULE_ENABLED */
40 /* #define HAL_CRYP_MODULE_ENABLED */
41 #define HAL_DAC_MODULE_ENABLED
42 /* #define HAL_DCMI_MODULE_ENABLED */
43 #define HAL_DMA_MODULE_ENABLED
44 /* #define HAL_DMA2D_MODULE_ENABLED */
45 /* #define HAL_ETH_MODULE_ENABLED */
46 #define HAL_FLASH_MODULE_ENABLED
47 /* #define HAL_NAND_MODULE_ENABLED */
48 /* #define HAL_NOR_MODULE_ENABLED */
49 /* #define HAL_PCCARD_MODULE_ENABLED */
50 /* #define HAL_SRAM_MODULE_ENABLED */
51 /* #define HAL_SDRAM_MODULE_ENABLED */
52 /* #define HAL_HASH_MODULE_ENABLED */
53 #define HAL_GPIO_MODULE_ENABLED
54 /* #define HAL_EXTI_MODULE_ENABLED */
55 #define HAL_I2C_MODULE_ENABLED
56 /* #define HAL_SMBUS_MODULE_ENABLED */
57 /* #define HAL_I2S_MODULE_ENABLED */
58 /* #define HAL_IWDG_MODULE_ENABLED */
59 /* #define HAL_LTDC_MODULE_ENABLED */
60 /* #define HAL_DSI_MODULE_ENABLED */
61 #define HAL_PWR_MODULE_ENABLED
62 /* #define HAL_QSPI_MODULE_ENABLED */
63 #define HAL_RCC_MODULE_ENABLED
64 /* #define HAL_RNG_MODULE_ENABLED */
65 #define HAL_RTC_MODULE_ENABLED
66 /* #define HAL_SAI_MODULE_ENABLED */
67 #define HAL_SD_MODULE_ENABLED
68 #define HAL_SPI_MODULE_ENABLED
69 #define HAL_TIM_MODULE_ENABLED
70 /* #define HAL_UART_MODULE_ENABLED */
71 /* #define HAL_USART_MODULE_ENABLED */
72 /* #define HAL_IRDA_MODULE_ENABLED */
73 /* #define HAL_SMARTCARD_MODULE_ENABLED */
74 /* #define HAL_WWDG_MODULE_ENABLED */
75 #define HAL_CORTEX_MODULE_ENABLED
76 #define HAL_PCD_MODULE_ENABLED
77 /* #define HAL_HCD_MODULE_ENABLED */
78 /* #define HAL_FMPI2C_MODULE_ENABLED */
79 /* #define HAL_SPDIFRX_MODULE_ENABLED */
80 /* #define HAL_DFSDM_MODULE_ENABLED */
81 /* #define HAL_LPTIM_MODULE_ENABLED */
82 /* #define HAL_MMC_MODULE_ENABLED */
83 
84 /* ########################## HSE/HSI Values adaptation ##################### */
85  /**
86  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
87  * This value is used by the RCC HAL module to compute the system frequency
88  * (when HSE is used as system clock source, directly or through the PLL).
89  */
90 #ifndef HSE_VALUE
91 #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */
92 #endif /* HSE_VALUE */
93 
94 #ifndef HSE_STARTUP_TIMEOUT
95 #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */
96 #endif /* HSE_STARTUP_TIMEOUT */
97 
98  /**
99  * @brief Internal High Speed oscillator (HSI) value.
100  * This value is used by the RCC HAL module to compute the system frequency
101  * (when HSI is used as system clock source, directly or through the PLL).
102  */
103 #ifndef HSI_VALUE
104 #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
105 #endif /* HSI_VALUE */
106 
107  /**
108  * @brief Internal Low Speed oscillator (LSI) value.
109  */
110 #ifndef LSI_VALUE
111 #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/
112 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
113 The real value may vary depending on the variations
114 in voltage and temperature.*/
115  /**
116  * @brief External Low Speed oscillator (LSE) value.
117  */
118 #ifndef LSE_VALUE
119 #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */
120 #endif /* LSE_VALUE */
121 
122 #ifndef LSE_STARTUP_TIMEOUT
123 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */
124 #endif /* LSE_STARTUP_TIMEOUT */
125 
126  /**
127  * @brief External clock source for I2S peripheral
128  * This value is used by the I2S HAL module to compute the I2S clock source
129  * frequency, this source is inserted directly through I2S_CKIN pad.
130  */
131 #ifndef EXTERNAL_CLOCK_VALUE
132 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the External audio frequency in Hz*/
133 #endif /* EXTERNAL_CLOCK_VALUE */
134 
135 /* Tip: To avoid modifying this file each time you need to use different HSE,
136  === you can define the HSE value in your toolchain compiler preprocessor. */
137 
138 /* ########################### System Configuration ######################### */
139  /**
140  * @brief This is the HAL system configuration section
141  */
142 #define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */
143 #define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */
144 #define USE_RTOS 0U
145 #define PREFETCH_ENABLE 1U
146 #define INSTRUCTION_CACHE_ENABLE 1U
147 #define DATA_CACHE_ENABLE 1U
148 
149 #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
150 #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
151 #define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */
152 #define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
153 #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
154 #define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
155 #define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */
156 #define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */
157 #define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */
158 #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
159 #define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
160 #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
161 #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
162 #define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */
163 #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
164 #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
165 #define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */
166 #define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */
167 #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
168 #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
169 #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
170 #define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
171 #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
172 #define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */
173 #define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
174 #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
175 #define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */
176 #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
177 #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
178 #define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */
179 #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
180 #define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */
181 #define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */
182 #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
183 #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
184 #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
185 #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
186 #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
187 
188 /* ########################## Assert Selection ############################## */
189  /**
190  * @brief Uncomment the line below to expanse the "assert_param" macro in the
191  * HAL drivers code
192  */
193 /* #define USE_FULL_ASSERT 1U */
194 
195 /* ################## Ethernet peripheral configuration ##################### */
196 
197 /* Section 1 : Ethernet peripheral configuration */
198 
199 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
200 #define MAC_ADDR0 2U
201 #define MAC_ADDR1 0U
202 #define MAC_ADDR2 0U
203 #define MAC_ADDR3 0U
204 #define MAC_ADDR4 0U
205 #define MAC_ADDR5 0U
206 
207 /* Definition of the Ethernet driver buffers size and count */
208 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
209 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
210 #define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
211 #define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
212 
213 /* Section 2: PHY configuration section */
214 
215 /* DP83848_PHY_ADDRESS Address*/
216 #define DP83848_PHY_ADDRESS 0x01U
217 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
218 #define PHY_RESET_DELAY ((uint32_t)0x000000FFU)
219 /* PHY Configuration delay */
220 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU)
221 
222 #define PHY_READ_TO ((uint32_t)0x0000FFFFU)
223 #define PHY_WRITE_TO ((uint32_t)0x0000FFFFU)
224 
225 /* Section 3: Common PHY Registers */
226 
227 #define PHY_BCR ((uint16_t)0x0000U) /*!< Transceiver Basic Control Register */
228 #define PHY_BSR ((uint16_t)0x0001U) /*!< Transceiver Basic Status Register */
229 
230 #define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */
231 #define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */
232 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */
233 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */
234 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */
235 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */
236 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */
237 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */
238 #define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */
239 #define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */
240 
241 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */
242 #define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */
243 #define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */
244 
245 /* Section 4: Extended PHY Registers */
246 #define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */
247 
248 #define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */
249 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */
250 
251 /* ################## SPI peripheral configuration ########################## */
252 
253 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
254 * Activated: CRC code is present inside driver
255 * Deactivated: CRC code cleaned from driver
256 */
257 
258 #define USE_SPI_CRC 0U
259 
260 /* Includes ------------------------------------------------------------------*/
261  /**
262  * @brief Include module's header file
263  */
264 
265 #ifdef HAL_RCC_MODULE_ENABLED
266 #include "stm32f4xx_hal_rcc.h"
267 #endif /* HAL_RCC_MODULE_ENABLED */
268 
269 #ifdef HAL_GPIO_MODULE_ENABLED
270 #include "stm32f4xx_hal_gpio.h"
271 #endif /* HAL_GPIO_MODULE_ENABLED */
272 
273 #ifdef HAL_EXTI_MODULE_ENABLED
274 #include "stm32f4xx_hal_exti.h"
275 #endif /* HAL_EXTI_MODULE_ENABLED */
276 
277 #ifdef HAL_DMA_MODULE_ENABLED
278 #include "stm32f4xx_hal_dma.h"
279 #endif /* HAL_DMA_MODULE_ENABLED */
280 
281 #ifdef HAL_CORTEX_MODULE_ENABLED
282 #include "stm32f4xx_hal_cortex.h"
283 #endif /* HAL_CORTEX_MODULE_ENABLED */
284 
285 #ifdef HAL_ADC_MODULE_ENABLED
286 #include "stm32f4xx_hal_adc.h"
287 #endif /* HAL_ADC_MODULE_ENABLED */
288 
289 #ifdef HAL_CAN_MODULE_ENABLED
290 #include "stm32f4xx_hal_can.h"
291 #endif /* HAL_CAN_MODULE_ENABLED */
292 
293 #ifdef HAL_CAN_LEGACY_MODULE_ENABLED
294 #include "stm32f4xx_hal_can_legacy.h"
295 #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
296 
297 #ifdef HAL_CRC_MODULE_ENABLED
298 #include "stm32f4xx_hal_crc.h"
299 #endif /* HAL_CRC_MODULE_ENABLED */
300 
301 #ifdef HAL_CRYP_MODULE_ENABLED
302 #include "stm32f4xx_hal_cryp.h"
303 #endif /* HAL_CRYP_MODULE_ENABLED */
304 
305 #ifdef HAL_DMA2D_MODULE_ENABLED
306 #include "stm32f4xx_hal_dma2d.h"
307 #endif /* HAL_DMA2D_MODULE_ENABLED */
308 
309 #ifdef HAL_DAC_MODULE_ENABLED
310 #include "stm32f4xx_hal_dac.h"
311 #endif /* HAL_DAC_MODULE_ENABLED */
312 
313 #ifdef HAL_DCMI_MODULE_ENABLED
314 #include "stm32f4xx_hal_dcmi.h"
315 #endif /* HAL_DCMI_MODULE_ENABLED */
316 
317 #ifdef HAL_ETH_MODULE_ENABLED
318 #include "stm32f4xx_hal_eth.h"
319 #endif /* HAL_ETH_MODULE_ENABLED */
320 
321 #ifdef HAL_FLASH_MODULE_ENABLED
322 #include "stm32f4xx_hal_flash.h"
323 #endif /* HAL_FLASH_MODULE_ENABLED */
324 
325 #ifdef HAL_SRAM_MODULE_ENABLED
326 #include "stm32f4xx_hal_sram.h"
327 #endif /* HAL_SRAM_MODULE_ENABLED */
328 
329 #ifdef HAL_NOR_MODULE_ENABLED
330 #include "stm32f4xx_hal_nor.h"
331 #endif /* HAL_NOR_MODULE_ENABLED */
332 
333 #ifdef HAL_NAND_MODULE_ENABLED
334 #include "stm32f4xx_hal_nand.h"
335 #endif /* HAL_NAND_MODULE_ENABLED */
336 
337 #ifdef HAL_PCCARD_MODULE_ENABLED
338 #include "stm32f4xx_hal_pccard.h"
339 #endif /* HAL_PCCARD_MODULE_ENABLED */
340 
341 #ifdef HAL_SDRAM_MODULE_ENABLED
342 #include "stm32f4xx_hal_sdram.h"
343 #endif /* HAL_SDRAM_MODULE_ENABLED */
344 
345 #ifdef HAL_HASH_MODULE_ENABLED
346 #include "stm32f4xx_hal_hash.h"
347 #endif /* HAL_HASH_MODULE_ENABLED */
348 
349 #ifdef HAL_I2C_MODULE_ENABLED
350 #include "stm32f4xx_hal_i2c.h"
351 #endif /* HAL_I2C_MODULE_ENABLED */
352 
353 #ifdef HAL_SMBUS_MODULE_ENABLED
354 #include "stm32f4xx_hal_smbus.h"
355 #endif /* HAL_SMBUS_MODULE_ENABLED */
356 
357 #ifdef HAL_I2S_MODULE_ENABLED
358 #include "stm32f4xx_hal_i2s.h"
359 #endif /* HAL_I2S_MODULE_ENABLED */
360 
361 #ifdef HAL_IWDG_MODULE_ENABLED
362 #include "stm32f4xx_hal_iwdg.h"
363 #endif /* HAL_IWDG_MODULE_ENABLED */
364 
365 #ifdef HAL_LTDC_MODULE_ENABLED
366 #include "stm32f4xx_hal_ltdc.h"
367 #endif /* HAL_LTDC_MODULE_ENABLED */
368 
369 #ifdef HAL_PWR_MODULE_ENABLED
370 #include "stm32f4xx_hal_pwr.h"
371 #endif /* HAL_PWR_MODULE_ENABLED */
372 
373 #ifdef HAL_RNG_MODULE_ENABLED
374 #include "stm32f4xx_hal_rng.h"
375 #endif /* HAL_RNG_MODULE_ENABLED */
376 
377 #ifdef HAL_RTC_MODULE_ENABLED
378 #include "stm32f4xx_hal_rtc.h"
379 #endif /* HAL_RTC_MODULE_ENABLED */
380 
381 #ifdef HAL_SAI_MODULE_ENABLED
382 #include "stm32f4xx_hal_sai.h"
383 #endif /* HAL_SAI_MODULE_ENABLED */
384 
385 #ifdef HAL_SD_MODULE_ENABLED
386 #include "stm32f4xx_hal_sd.h"
387 #endif /* HAL_SD_MODULE_ENABLED */
388 
389 #ifdef HAL_SPI_MODULE_ENABLED
390 #include "stm32f4xx_hal_spi.h"
391 #endif /* HAL_SPI_MODULE_ENABLED */
392 
393 #ifdef HAL_TIM_MODULE_ENABLED
394 #include "stm32f4xx_hal_tim.h"
395 #endif /* HAL_TIM_MODULE_ENABLED */
396 
397 #ifdef HAL_UART_MODULE_ENABLED
398 #include "stm32f4xx_hal_uart.h"
399 #endif /* HAL_UART_MODULE_ENABLED */
400 
401 #ifdef HAL_USART_MODULE_ENABLED
402 #include "stm32f4xx_hal_usart.h"
403 #endif /* HAL_USART_MODULE_ENABLED */
404 
405 #ifdef HAL_IRDA_MODULE_ENABLED
406 #include "stm32f4xx_hal_irda.h"
407 #endif /* HAL_IRDA_MODULE_ENABLED */
408 
409 #ifdef HAL_SMARTCARD_MODULE_ENABLED
410 #include "stm32f4xx_hal_smartcard.h"
411 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
412 
413 #ifdef HAL_WWDG_MODULE_ENABLED
414 #include "stm32f4xx_hal_wwdg.h"
415 #endif /* HAL_WWDG_MODULE_ENABLED */
416 
417 #ifdef HAL_PCD_MODULE_ENABLED
418 #include "stm32f4xx_hal_pcd.h"
419 #endif /* HAL_PCD_MODULE_ENABLED */
420 
421 #ifdef HAL_HCD_MODULE_ENABLED
422 #include "stm32f4xx_hal_hcd.h"
423 #endif /* HAL_HCD_MODULE_ENABLED */
424 
425 #ifdef HAL_DSI_MODULE_ENABLED
426 #include "stm32f4xx_hal_dsi.h"
427 #endif /* HAL_DSI_MODULE_ENABLED */
428 
429 #ifdef HAL_QSPI_MODULE_ENABLED
430 #include "stm32f4xx_hal_qspi.h"
431 #endif /* HAL_QSPI_MODULE_ENABLED */
432 
433 #ifdef HAL_CEC_MODULE_ENABLED
434 #include "stm32f4xx_hal_cec.h"
435 #endif /* HAL_CEC_MODULE_ENABLED */
436 
437 #ifdef HAL_FMPI2C_MODULE_ENABLED
438 #include "stm32f4xx_hal_fmpi2c.h"
439 #endif /* HAL_FMPI2C_MODULE_ENABLED */
440 
441 #ifdef HAL_SPDIFRX_MODULE_ENABLED
442 #include "stm32f4xx_hal_spdifrx.h"
443 #endif /* HAL_SPDIFRX_MODULE_ENABLED */
444 
445 #ifdef HAL_DFSDM_MODULE_ENABLED
446 #include "stm32f4xx_hal_dfsdm.h"
447 #endif /* HAL_DFSDM_MODULE_ENABLED */
448 
449 #ifdef HAL_LPTIM_MODULE_ENABLED
450 #include "stm32f4xx_hal_lptim.h"
451 #endif /* HAL_LPTIM_MODULE_ENABLED */
452 
453 #ifdef HAL_MMC_MODULE_ENABLED
454 #include "stm32f4xx_hal_mmc.h"
455 #endif /* HAL_MMC_MODULE_ENABLED */
456 
457 /* Exported macro ------------------------------------------------------------*/
458 #ifdef USE_FULL_ASSERT
459  /**
460  * @brief The assert_param macro is used for function's parameters check.
461  * @param expr: If expr is false, it calls assert_failed function
462  * which reports the name of the source file and the source
463  * line number of the call that failed.
464  * If expr is true, it returns no value.
465  * @retval None
466  */
467 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
468 /* Exported functions ------------------------------------------------------- */
469 void assert_failed(uint8_t *file, uint32_t line);
470 #else
471 #define assert_param(expr) ((void)0U)
472 #endif /* USE_FULL_ASSERT */
473 
474 #ifdef __cplusplus
475 }
476 #endif
477 
478 #endif /* __STM32F4xx_HAL_CONF_H */
479 
480 
481 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
stm32f4xx_hal_hcd.h
Header file of HCD HAL module.
stm32f4xx_hal_pcd.h
Header file of PCD HAL module.
stm32f4xx_hal_tim.h
Header file of TIM HAL module.
stm32f4xx_hal_adc.h
Header file containing functions prototypes of ADC HAL library.
stm32f4xx_hal_iwdg.h
Header file of IWDG HAL module.
stm32f4xx_hal_cortex.h
Header file of CORTEX HAL module.
stm32f4xx_hal_uart.h
Header file of UART HAL module.
stm32f4xx_hal_eth.h
Header file of ETH HAL module.
stm32f4xx_hal_i2c.h
Header file of I2C HAL module.
stm32f4xx_hal_dma.h
Header file of DMA HAL module.
stm32f4xx_hal_spi.h
Header file of SPI HAL module.
uint8_t
const uint8_t[]
Definition: 404_html.c:3
stm32f4xx_hal_rcc.h
Header file of RCC HAL module.
stm32f4xx_hal_gpio.h
Header file of GPIO HAL module.
stm32f4xx_hal_pwr.h
Header file of PWR HAL module.
stm32f4xx_hal_flash.h
Header file of FLASH HAL module.