Prusa MINI Firmware overview
Main Page
Modules
Classes
Files
File List
File Members
pins_MELZI_CREALITY.h
Go to the documentation of this file.
1
/**
2
* Marlin 3D Printer Firmware
3
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
4
*
5
* Based on Sprinter and grbl.
6
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
7
*
8
* This program is free software: you can redistribute it and/or modify
9
* it under the terms of the GNU General Public License as published by
10
* the Free Software Foundation, either version 3 of the License, or
11
* (at your option) any later version.
12
*
13
* This program is distributed in the hope that it will be useful,
14
* but WITHOUT ANY WARRANTY; without even the implied warranty of
15
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16
* GNU General Public License for more details.
17
*
18
* You should have received a copy of the GNU General Public License
19
* along with this program. If not, see <http://www.gnu.org/licenses/>.
20
*
21
*/
22
#pragma once
23
24
/**
25
* Melzi (Creality) pin assignments
26
*
27
* The Creality board needs a bootloader installed before Marlin can be uploaded.
28
* If you don't have a chip programmer you can use a spare Arduino plus a few
29
* electronic components to write the bootloader.
30
*
31
* See http://www.instructables.com/id/Burn-Arduino-Bootloader-with-Arduino-MEGA/
32
*/
33
34
#define BOARD_INFO_NAME "Melzi (Creality)"
35
36
#include "
pins_MELZI.h
"
37
38
// For the stock CR-10 use the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
39
// option for the display in Configuration.h
40
41
#undef LCD_SDSS
42
#undef LED_PIN
43
#undef LCD_PINS_RS
44
#undef LCD_PINS_ENABLE
45
#undef LCD_PINS_D4
46
#undef LCD_PINS_D5
47
#undef LCD_PINS_D6
48
#undef LCD_PINS_D7
49
#undef FIL_RUNOUT_PIN // Uses Beeper/LED Pin Pulled to GND
50
51
#define LCD_SDSS 31 // Smart Controller SD card reader (rather than the Melzi)
52
#define LCD_PINS_RS 28 // ST9720 CS
53
#define LCD_PINS_ENABLE 17 // ST9720 DAT
54
#define LCD_PINS_D4 30 // ST9720 CLK
55
56
#if ENABLED(BLTOUCH)
57
#define SERVO0_PIN 27
58
#undef BEEPER_PIN
59
#endif
60
61
// Alter timing for graphical display
62
#ifndef ST7920_DELAY_1
63
#define ST7920_DELAY_1 DELAY_NS(125)
64
#endif
65
#ifndef ST7920_DELAY_2
66
#define ST7920_DELAY_2 DELAY_NS(125)
67
#endif
68
#ifndef ST7920_DELAY_3
69
#define ST7920_DELAY_3 DELAY_NS(125)
70
#endif
71
72
#if ENABLED(MINIPANEL)
73
#undef DOGLCD_CS
74
#define DOGLCD_CS LCD_PINS_RS
75
#endif
76
77
/**
78
PIN: 0 Port: B0 E0_DIR_PIN protected
79
PIN: 1 Port: B1 E0_STEP_PIN protected
80
PIN: 2 Port: B2 Z_DIR_PIN protected
81
PIN: 3 Port: B3 Z_STEP_PIN protected
82
PIN: 4 Port: B4 AVR_SS_PIN protected
83
. FAN_PIN protected
84
. SS_PIN protected
85
PIN: 5 Port: B5 AVR_MOSI_PIN Output = 1
86
. MOSI_PIN Output = 1
87
PIN: 6 Port: B6 AVR_MISO_PIN Input = 0 TIMER3A PWM: 0 WGM: 1 COM3A: 0 CS: 3 TCCR3A: 1 TCCR3B: 3 TIMSK3: 0
88
. MISO_PIN Input = 0
89
PIN: 7 Port: B7 AVR_SCK_PIN Output = 0 TIMER3B PWM: 0 WGM: 1 COM3B: 0 CS: 3 TCCR3A: 1 TCCR3B: 3 TIMSK3: 0
90
. SCK_PIN Output = 0
91
PIN: 8 Port: D0 RXD Input = 1
92
PIN: 9 Port: D1 TXD Input = 0
93
PIN: 10 Port: D2 BTN_EN2 Input = 1
94
PIN: 11 Port: D3 BTN_EN1 Input = 1
95
PIN: 12 Port: D4 HEATER_BED_PIN protected
96
PIN: 13 Port: D5 HEATER_0_PIN protected
97
PIN: 14 Port: D6 E0_ENABLE_PIN protected
98
. X_ENABLE_PIN protected
99
. Y_ENABLE_PIN protected
100
PIN: 15 Port: D7 X_STEP_PIN protected
101
PIN: 16 Port: C0 BTN_ENC Input = 1
102
. SCL Input = 1
103
PIN: 17 Port: C1 LCD_PINS_ENABLE Output = 0
104
. SDA Output = 0
105
PIN: 18 Port: C2 X_MIN_PIN protected
106
. X_STOP_PIN protected
107
PIN: 19 Port: C3 Y_MIN_PIN protected
108
. Y_STOP_PIN protected
109
PIN: 20 Port: C4 Z_MIN_PIN protected
110
. Z_STOP_PIN protected
111
PIN: 21 Port: C5 X_DIR_PIN protected
112
PIN: 22 Port: C6 Y_STEP_PIN protected
113
PIN: 23 Port: C7 Y_DIR_PIN protected
114
PIN: 24 Port: A7 TEMP_0_PIN protected
115
PIN: 25 Port: A6 TEMP_BED_PIN protected
116
PIN: 26 Port: A5 Z_ENABLE_PIN protected
117
PIN: 27 Port: A4 BEEPER_PIN Output = 0
118
PIN: 28 Port: A3 LCD_PINS_RS Output = 0
119
PIN: 29 Port: A2 <unused/unknown> Input = 0
120
PIN: 30 Port: A1 LCD_PINS_D4 Output = 1
121
PIN: 31 Port: A0 SDSS Output = 1
122
*/
pins_MELZI.h
Prusa-Firmware-Buddy-Private1
lib
Marlin
Marlin
src
pins
sanguino
pins_MELZI_CREALITY.h
Generated by
1.8.16